How to Flush Transmission Fluid
Oct 08, · In this video I am going to show you how you can replace the transmission fluid and filter but also more important how you can do a DIY transmission fluid fl. Open the case of transmission fluid and remove the caps from all of the transmission fluid. Once you start the vehicle it will start pumping the transmission fluid out into the 5 gallon bucket. You will need to add fluid quickly. Start the vehicle (or have your helper do it) and then start adding transmission fluid through the funnel.
If you have an automatic transmission in your vehicle then you should have the transmission fluid flushed to keep your vehicle well maintained.
The transmission is often forgotten until problems arise. By then it is too late and you end up with costly repairs. It is best to flush the transmission fluid every 30, miles or three years. More often if the vehicle is used for towing. Most auto repair shops want you to believe that you have to use their expensive machine to flush your automatic transmission fluid. This article will show you how to do it at home with how to draw a cartoon girls few simple tools.
Get everything you need ready before you start the transmission flush service. Once you start you don't need to stop until you are finished. Run the vehicle until it gets to normal operating temperature and then turn it off. Raise the front of the vehicle with the jack and place it on jack stands. Now you will need to find where how to use paypoint machine transmission cooler lines go into the radiator.
They may either be on the sides or on the bottom of the radiator. Place the 5 gallon bucket under where the transmission cooler lines go into the radiator. Loosen the hose clamps on the transmission cooler lines at the radiator and slide them back onto the lines. Hold the transmission cooler line where it goes into the radiator and pull them off.
If they haven't been removed in a long time you may need to twist them while pulling them off. Once you have both transmission cooler lines removed and in the bucket remove the transmission dipstick and place the long funnel into the tube.
Open the case of transmission fluid and remove the caps from all of the transmission fluid. Once you start the vehicle it will start pumping the transmission fluid out into the 5 gallon bucket.
You will need to add fluid quickly. Start the vehicle or have your helper do it and then start adding transmission fluid through the funnel.
Pour the transmission fluid quickly, and try not what is a suppressor spark plug let the funnel run dry. Pour 9 of the 12 quarts of transmission fluid into the funnel and then shut the vehicle off.
You want to leave about 3 quarts available in case you need to top off the transmission fluid. Now replace the transmission cooler lines and remove the vehicle from the jack stands and lower it back to the ground. Start the vehicle and make sure it is up to normal operating temperature. With your foot on the brake pedal move the vehicle through all of the gears several times and then place it back in park. Now insert the dipstick and check the fluid level. If it is within the normal range then you have completed the transmission flush service.
If you need to add more fluid; add about half a quart at a time and then run the vehicle through the gears again and recheck the level. Do this until the level is within the normal range. If you have too much fluid then you will need to drain some of it until it is within the normal range. Shut the vehicle off and locate the drain plug and let a little fluid out.
Replace the drain plug and then start the vehicle and check the fluid level again. This article was written by a professional writer, copy edited and fact checked through a multi-point auditing system, in efforts to ensure our readers only receive the best information. To submit your questions or ideas, or to simply learn more, see our about us page: link below. Step 1 Get everything you need ready before you start the transmission what causes acne back acne service.
Step 2 Loosen the hose clamps on the transmission cooler lines at the radiator and slide them back onto the lines. Step 3 Open the case of transmission fluid and remove the caps from all of the transmission fluid. Tips A helper makes this how to flush a transmission fluid little easier so that they can start and shut off the vehicle for you and you can focus on the transmission flush service.
Always make sure that you leave a few quarts of transmission fluid so that you will have some to add in case you need it. Transmission repairs get expensive. It is a lot easier to pay a little for a transmission flush service every few years than it is to pay to rebuild or replace your transmission.
Long funnel that will fit into the transmission dipstick tube. Case of automatic transmission fluid. Check the dipstick or owner's manual for your vehicle's appropriate transmission fluid A helper makes this easier. Jack and jack stands. DO NOT perform a transmission flush service if the vehicle has high mileagemiles or more and the transmission has never been flushed before.
This can remove the buildup of varnish in the transmission and lead to sticking valves and result in costly repairs. Keep your hands clear of moving parts in the engine bay.
Transmission Fluid Flush Vs Change
Nov 13, · Nissan Frontier 4x4. While this is the recommended transmission service interval, the lifespan of transmission fluid can vary depending on use. By sticking to this recommended 30, miles transmission fluid change interval, you can help keep your transmission fluid clean and prevent the fluid from breaking down over time, which it would if you do not get it changed. Transmission Flush - Replaces % of your transmission fluid and purges accumulated particles and deposits from the entire transmission. Fluid is expelled from your transmission using a cooler line flushing machine or a pump inlet. The transmission pan is inspected and cleaned, the filter replaced. A complete batch of new, pure ATF is added.
One of the most important parts of car maintenance involves flushing out and replacing the transmission fluid. It is true a lot of people take their cars in to have their transmission flushed and new fluid put in.
That does not have to be the case for you. If you want to save money, you can do it yourself relatively easy instead of taking it to a garage. Of course, you need to be willing to get a little dirty doing it.
Do not work on the vehicle if it is only being supported by a car jack. You should have the vehicle up on car ramps and on a flat surface. Remove your transmission dip stick.
A lot of transmissions have drain plugs, so you will need to locate this and then put your drain pan under that area of the transmission. If your transmission does not have a drain plug then make sure to place your drain pan directly under the transmission pan and begin removing every other transmission bolt. You will need to leave 2 of the transmission bolts on each side of the transmission but remove the rest of them and set aside.
On one side, carefully remove the 2 bolts so the transmission fluid will begin to leak out. On the other side, begin to loosen the bolts very slowly. When it feels like the bolts are 2 or 3 threads from coming off, immediately push the transmission pan up and then remove the other 2 bolts and set aside as well.
After all of the bolts are out, lower the pan and let the fluid flow into the drain pan. You should inspect the drain pan for debris. Use a drill with a wire wheel to remove the old transmission gasket. You can also use a scraper to remove the gasket as well. Transmission pans usually have a magnet that collects some of the metal dust. Make sure to clean the magnet off. Then clean off the transmission pan. After you have done that replace the magnet.
Make sure that the holes for mounting on the new filter match exactly to the old filter, otherwise the filter will not fit in your transmission. Do a visual check before proceeding. Remove the old filter by removing the mounting bolts. More fluid will probably come out when you are doing this so make sure the drain pan is in place.
Remove the old filter and put it in a plastic bag that can be thrown away properly. After you have done this, get out from under the car and let the transmission drain for at least 1 hour before doing anything else to it.
After the transmission is drained you will now install the new filter. Put the drain plug back in. Grease the gasket with wheel bearing grease. Tighten the bolts for the transmission pan. Make sure that it is every other one that you tighten. Make sure not to tighten any more than 15 to 20 inch per pound. After the pan bolts are properly torqued, clean the area and lower the car.
Boat Repair: Fixing the Trailer. I've watched a couple videos and read a few articles about doing a transmis Read More. Is clutch fluid the manual transmission oil? I had its brake fluid and My boy has a Nissan Sentra 2.
Transmission oil cooler line broke DIY Transmission Flush. JDeere L check transmission fluid? I have a John Deere L and want to make sure the transmission fluid is at Popular Articles. Troubleshooting a Faulty Transmission Fi Troubleshooting a Faulty Transmission Filter. How to Change Transmission Fluid. By Don P. How to Repair Leaking Transmission Coole How to Change a Car Flywheel.
How to Drain Transmission Fluid. By Jude Barton.