How to install a plasma tv above a fireplace

how to install a plasma tv above a fireplace

Solved! Why It’s a Mistake to Mount a TV Above a Fireplace

May 03,  · Tips that you should know. Here are important tips about mounting your TV above the fireplace: Treat The TV Like an Art: Your television should be attached to the same altitude as you want to hang some pieces of art with the same dimension above your house fireplace. If you’re in great Doubt, Do a Bit of Math: Depends on the height of the mantel — or if ever you do not have one, at the. Before you decide to install a TV above your fireplace, it is advisable to place a thermometer above the mantel and make a fire. Monitor the temperature over an hour or so and make sure it does not exceed 90°F. If the temperature remains below 90°F, it is safe to mount a TV above your fireplace.

Few things are cozier than watching television next to a crackling fire. But what about when the TV itself is above the fireplace? Both activities seem to fit together. Plus, due to the layout of some homes, this is often the best arrangement—in some cases, the only arrangement. But is it ever good practice to mount a TV above a fireplaceeither from the standpoint of viewing comfort or safety? In particular, will a TV or any other video monitor become damaged from the nearby heat of the fireplace?

While you can mount a TV above a fireplaceyou should try to place the TV in another location, if possible, due to viewing and safety limitations. The issues with mounting the TV above a fireplace center more around the quality of the viewing experience and with user comfort than with damage to the electronics. However, in some cases, a fire might become hot enough to surpass the safe temperature range for your equipment's internal electronics and even the lower part of the casing.

Best if jacks and plugs are already mounted there and it may be more difficult or costly to relocate them. With fireplace mantels 50 to 60 inches high, placing the TV above the fireplace raises the screen viewing height too high.

Unlike the cathode ray televisions of the past, which drew from 65 to watts depending on size, current TV and video monitors produce relatively little heat. The operable word is relative since screens keep getting larger.

Plasma TVs —no longer sold but still found on secondary markets—can draw as much as watts. Enclosures are vented to allow the heat produced locally what is a pink elephant gift exchange the electronics to escape. Subjecting the TV to additional heat can counteract the TV's normal operations.

Sample temperature ranges from a few major manufacturers demonstrate just how low the upper ends of these ranges can be:. Consult the instructions included with your TV for the correct height, angle, and distance you should maintain from the screen.

Typically, the center of the screen should be at eye height when you are sitting and facing the screen. Unless the fireplace is especially low, its height will conflict with optimal viewing height for the TV.

Additionally, with the advent of 4K TVs, the optional viewing angle has increased. A standard inch high-definition TV should be viewed no closer than 83 inches away. But due to the greater how to install a plasma tv above a fireplace of pixels displayed by 4K TVs, the recommended optional minimum distance is half of that 39 inches. As distance decreases, the viewing angle increases.

If you like viewing your screen as close as possible, the angle imposed by the fireplace will detract from your viewing experience. While a full motion articulating wall mount can help to angle the screen downward, you are still forced to tip your head back to see the screen.

Fireplace mantels range from 50 to 60 inches tall. Sixty inches is 5 feet tall. True film lovers abhor distraction.

Ambient light and background activity combine to take away from the best cinematic experience. The licking flames of even a modest fireplace represent both light and activity. If you value premium picture quality, a fireplace underneath the TV is not conducive to a peak cinematic experience. With its crackle and smoke, an authentic wood fire is charming and romantic. But intense heat and smoke are bad for TVs that are mounted above them.

Wood fires can put out as much as 60, BTUs British Thermal Units and can reach temperatures high enough to ignite creosote in the flue and start chimney fires. Since heat risesany heat not vented up what to mix with cognac hennessy chimney cascades over the front of the mantel and upward.

If the heat doesn't affect the TV, the smoke might. At the same time, heat rising from a fireplace quickly dissipates. Heat measured directly above the top lip of the fireplace box will be different from heat even a foot or two above that location.

The only way to know if the area where you intend to mount the TV is too hot is by taking temperature readings. Brick, natural stone, manufactured veneer stoneand similar solid masonry fireplaces afford no below-surface room to run wires.

As a result, the wires would need to be run on top of the surface. By most electrical codes, NM electrical cable cannot be surface-mounted. The only code-compliant alternative would be to run wires through surface-level conduit, hardly an attractive feature for any fireplace. Houses and apartments are often built with recessed niches intended for TV placement. These niches also have an electrical outlet, Ethernet cable, and cable What day of the week was i born formula jack.

Still, many people tend to prefer the reliability and faster speeds of the Ethernet connection. If your home has a recessed niche above the fireplace with all of the connections you desire, there is no reason why you cannot place a TV there. When you need to maximize your small living room and pack in as many functions as possible, you may want to mount the TV above the fireplace.

Placing the TV in this area frees up wall space for other elements such as bookcases, furniture, or wall art. Small living rooms demand creative thinking to make everything fit together, and placing the TV above the fireplace may be one way to accomplish this. Over time, home fireplaces have increasingly become cooler. Intensely hot wood fires are becoming a thing of the past, as more communities enact air-quality restrictions and fewer wood fireplaces are being built. Natural gas fireplaces with inserts, particularly ventless gas fireplaces, are considerably cooler.

At the low end of the temperature scale are gel fireplaceswhich put out less heat than both wood and natural gas fireplaces. Actively scan device characteristics for identification. Use precise geolocation data. Select personalised content. Create a personalised content profile. Measure ad performance. Select basic ads. Create a personalised ads profile. Select personalised ads. Apply market research to generate audience insights. Measure content performance.

Develop and improve products. List of Partners vendors. Good Idea. Poor Idea. Read More. Your Privacy Rights. To change or withdraw your how to make a sugar cube igloo choices for TheSpruce. At any time, you can update your settings through the "EU Privacy" link at the bottom of any page. These choices will be signaled globally to our partners and will not affect browsing data.

We and our partners process data to: Actively scan device characteristics for identification. I Accept Show Purposes.

Site Navigation

The only thing about having a tv over the fp is that I don't like it when the fireplace is shorter in width than the tv, seems to be unbalanced and top heavy. The tv needs to be smaller than the fireplace, you can trick the eye by extending the width with a dark tile or larger frame. The TV . While you can mount a TV above a fireplace, you should try to place the TV in another location, if possible, due to viewing and safety limitations. The issues with mounting the TV above a fireplace center more around the quality of the viewing experience and with user comfort than with damage to . Some people like their plasma TV to be installed over fire place. Before .. you decide to install the plasma TV over the fireplace, make sure that the television does not get damaged due to the heat from the fireplace. However, a brick fireplace is more secure as it can very well support the weight of the TV.

A flat panel TV above your fireplace is very cool until you try and hide the cables. The fireplace prevents running the cables straight down the wall and the stud framing prevents running the cables laterally inside the wall. If your fireplace is on an interior wall, you may be able to go up the wall, however, that doesn't work on exterior walls. The top plate of the wall blocks access to the attic and the roof prevents drilling down from above.

The typical solution is to cut access holes in the walls and run the cables. In our older home, the walls are wood paneling which has been covered in heavy wallpaper and painted. Not an easy thing to repair without obvious blemishes remaining. A second option is to use the mantel to hide the cables and that is the option I chose. To my amazement, this worked very well. This instructable will show you how to use a board, a hinge and a magnet to run cables down to the floor left of fireplace.

I also discuss alternatives to accomplish the same thing without using a hinge. Hopefully, this will provide you with some good ideas for your home.

I love this new 50" Panasonic plasma smart tv. This picture shows how the cables are hidden in the mantel piece.

The hinge on the old barn wood opens a door for access to the cables. The cracked and worn nature of the wood makes the door virtually invisible as it appears to be a split in the wood. There are other ways to accomplish the same effect without using a hinge and I'll discuss those options as we go along. Before you decide to install a TV above your fireplace, it is advisable to place a thermometer above the mantel and make a fire. It is also advisable to check your local codes for running cables.

You will also need to use a stud finder and mark the location of the wall studs. The wall stud locations will determine where you will make the wall holes for access. This is especially true for the hole near the edge of the fireplace as this is a common place for a single or double stud.

In my case, there were 2 studs to the left of the fireplace which I had to drill through but that wasn't really a problem.

The first step is to find a big chunk of barn wood chunk size may vary or whatever wood you prefer. This chunk is a rough cut 2x4 from our old barn which measures a full 2" x 4" and is 8' long. Since my fireplace is 6' wide this board worked well after a bit, or a lot, of clean up. Determine the distance from the end of the board to the point where your cables will be coming down the wall. You'll want to locate your hinge a few inches further from the end of the board to accomodate the cables.

It's easiest to attach the hinge prior to cutting the access door and then remove it. In this way, you know the holes are drilled so the edges of the door line up with the rest of the board.

I didn't have any rusty screws so I spattered some new ones with brown metal primer and flat black paint from spray cans. To cut the door I used my tablesaw and jigsaw. Other choices would be a bandsaw or hand saw.

I finished the cut along the top edge of the mantle piece with a jigsaw because the blade is much thinner. This made the door gap unnoticeable. I'm guessing most of you aren't planning on using barn wood and hinges to hide your TV cables so here's a few alternative plans.

One board would be fastened to the wall and the front board would be held by rare earth magnets to the rear board. Magnets would be counter sunk and glued in one board and metal washers counter sunk in the other. When finished, the front board would simply snap into place and could be easily removed when necessary. The boards could have a variety of appearances from plain 4" boards to fancy trim boards. A third option is to simply cut a groove in the wall itself and cover it with a piece of trim.

This is possibly the easiest technique, however, you will not be able to easily access the cables without removing the trim. Considering the likelihood that we would be running additional cables in the future, I opted for having access to the cabling via a door.

Drill two 3" holes at either end of the rear board where the cables will enter and exit the channel. I opted to make the holes as large as possible since strength was not an issue.

This was especially true for the hole at the end of the board since I knew I would need to drill laterally through some studs. Before you start this step, make sure you have marked the location of all the wall studs.

This allows you to make your access holes between the studs and not over them. It also tells you where to place your nails for fastening the board to your wall.

Additionally, know where the edges of your TV will be so the access hole is completely hidden by the TV. It kinda defeats the purpose if it's not; Set your mantel board on the mantel and trace the circles as a drilling guide on to the wall. Pic 2 shows the hole I drilled through the double stud on the left side of the fireplace. Thankfully, the bit was long enough. Next, secure the mantel board to the wall using nails placed into the wall studs.

Last but not least The trick is getting the first pull string in place. Aluminum is nice as it is nonmagnetic and won't interfere as you work. If you are working on an interior wall, this won't be a problem as only exterior walls are insulated.

Overall, it wasn't very difficult to place and guide the string down to the exit hole near the floor. Once you have your first string run, tie multiple strings to it and pull them back up to the mantel top.

How many cables you plan to run will determine the number of strings to pull. The 5th string will remain in the wall for future use. Next, pull your cables one at a time. What worked well for me was to tie the string securely behind the plug and then cover the cable end with electrical tape. This helps the cable follow the string and eliminates any edges on the plug which might get hung up. Make sure you have your other strings secured so they do not get pulled along with the cable.

It is a good idea to tape the extra strings to the mantel with packing tape. Pull all necessary cables and secure the remaining pull string in the wall for future use. Hook up your TV and you're done! I hope this instructable was helpful and sparked some ideas for running cables above a fireplace. Thanks for checking it out and I look forward to your comments and suggestions for improvement. Reply 4 years ago. Our fireplace is more for show as we rarely use it.

That said it's not close to the chimney itself and I used an extension cord. Certainly not code. Ideally installing a wired outlet would be better.

Did you have any problem mounting your TV above the fireplace? Did you hit hardyboard or anything like that? Reply 6 years ago on Introduction. Please advice me regarding this!!! Reply 7 years ago on Introduction. Thanks for sharing the use of magnets to guide the string behind the wall. This will come in handy for some projects we have planned. Many people install tvs like this, but you'll get a stiff neck with it that high. It's generally accepted that a tv should be close to eye level of your normal viewing position, typically sitting on the couch.

My 42" tv is on a pivoting wall mount so I can reach the ports and is centered at about waist level. I built a wooden coffee table sized cabinet that fits under it with 6 shelves for all the AV components. Snaking an appliance AC line cord through a wall cavity is a violation of the National Electric Code. See NEC article , uses not permitted for flexible cable.

You can snake the low power wiring but you need to install an AC receptacle behind the TV. There are low profile specialty boxes made for this purpose. Probably not going to burn the house down but it is an unrated, probably Chinese made, cable run behind a fireplace - just saying Reply 8 years ago on Introduction. Thanks for the heads up. I thought that was pretty shaky myself but wanted to get the TV up.

Super Bowl deadline. Exactly why I left that extra pull string. I have always used a duct tape on a coat hanger wire for short wire rune, but this could be useful in tricky and unusual situations. I second the importance of leaving at least one additional string in the wall along with the wires you install since you will invariably need to install other ones in the future.

2 thoughts on “How to install a plasma tv above a fireplace

Add a comment

Your email will not be published.. Required fields are marked *