How to replace a bathroom tub

how to replace a bathroom tub

Upgrade Your Bathroom with These Tips on Removing and Replacing an Old Bathtub

Remove the tub spout and remove the wall surface all around the tub to a height of about 8 inches. (If there are tub faucet handles, leave them in place if they are at least 8 inches above the tub.) Use a flat pry bar or putty knife to pry off tiles. Cut through drywall with a drywall saw. Apr 28,  · Checkout my video on installing the Tile: elvalladolid.com a complete list of tools and materials needed, visit elvalladolid.com

Swapping how to become a boy scout merit badge counselor your dated tub for an updated unit is a doable DIY project with our tips on choosing and installing a new bathtub. If your bathtub is leaking, worn, cracked, or just looking tired, it might be time to upgrade to a new one. A standard bathtub replacement can be purchased at your local home center and installed by a plumbing professional.

However, removing the old tub and installing its stand-in can be time-consuming and costly, so buy the best bathtub you can afford to ensure you won't have to repeat the process for another 15 or 20 years.

And if you'd prefer to take a DIY route, we'll show you how to remove the tub yow your own in our step-by-step guide to replacing a bathtub below. Because you're swapping out an existing tub, your options will be limited by the current tub's dimensions, as well as the size of your bathroom's doorway. Before buying a new tub, you'll need to know the tub's exact width and length measurements and where the drain is placed left, right, or center.

An inexpensive replacement tub may be narrower than the old tub. Many people find a narrow tub uncomfortable, so be sure to consider comfort before you buy. Rrplace tubs fit into a inch opening, but some older ones can be longer. Measure to make sure your replacement tub will fit. Some spa or whirlpool tubs fit a standard tub opening, and installing one is not much more work than installing a standard tub, although a spa or whirlpool needs to plug into a GFCI ground fault circuit interrupter electrical receptacle.

Materials matter when shopping for a new bathtub. Acrylic or fiberglass tubs are inexpensive, light, and easy to install. Some have finishes that are fairly durable, but they can become dull in time. An enameled steel tub has a sturdier finish but lacks insulating properties, so bathwater will typically cool quickly. Enameled cast iron is the most expensive and heaviest material but might be worth the cost because it retains a gleaming finish for decades, fills quietly, and keeps water warm the longest.

Generally, standard bathtubs feature decorative aprons on an exposed side s and are found in white, biscuit, and cream, though other colors such as black, pastel blue, and pink finishes are available on midrange and pricier tubs. Rectangular tubs can feature rectangular, hourglass, or oval interiors, so give each bathtub you're considering a test run if possible. Lay down in the bathtub to check fit and comfort level.

Integrated seats, available on some midrange bathtubs, introduce added convenience while tubs with a curved apron wall supply extra bathing space. The prices of standard bathtubs vary more by material than design. Here's a look at the typical costs and the pros and cons associated with the most common types of standard bathtubs. Less expensive and lighter in weight than cast iron, these tubs chip somewhat easily, can be slippery, allow water to cool quickly, x offer limited color choices.

Available in a wide range of colors, these tubs are durable and retain heat, but they are also heavy and might require additional structural support. Lightweight, fade-resistant, and available in batrhoom styles with integrated comfort features, acrylic tubs hold heat well when insulated but might show scratches. Polyester gel coat finishes and fiberglass backing often supported by wood or metal framing create a batnroom, lightweight tub in many styles.

Americast by American Standard and UltraCast by Briggs are examples of materials that combine heavy-gauge steel, porcelain enamel, and resins to build bathtubs that offer all the benefits of cast iron at half the weight. Removing the bathtub yourself isn't all that difficult.

Before you begin, measure the tub and make sure you'll what is a contour plot able to get it past other fixtures and out the door.

Remove the sink or the toilet if they will be in how to make bajan seasoning way. To protect the floor, cut and tape pieces of plywood to the floor and cover with a drop cloth.

Then follow these steps on how to remove your old tub. From inside the tub, unscrew and remove the overflow cover plate.

If a drain assembly is attached to it, pull it out. A drain assembly with a plunger is shown. Unscrew and remove the mounting bracket if there is one.

To disconnect the drain, you might need to remove a screw or two and remove the strainer. You could also need to lift out a stopper and a rocker assembly. Use a strainer wrench to remove the drain flange. From an access panel behind the tub or from below, disconnect the waste-and-overflow WO unit from the drain line. Depending on the installation, you might need to unscrew a slip nut or loosen the screws on a no-hub coupling. If the parts are cemented plastic, you'll have to cut through a pipe.

Remove the WO unit from the tub. You might not need to remove the old WO unit if it will fit exactly on the new tub. Measure carefully. Remove the tub spout and remove the wall surface what is ati catalyst software around the tub to a height of about 8 inches. If there are tub faucet handles, leave them in place if they are at least 8 inches above the tub.

Use a flat pry bar or putty knife to pry off tiles. Cut through drywall with a drywall saw. If the wall is plaster, use a reciprocating saw, taking care not to cut into the studs. Pry off nails or unscrew screws. Pry out or unscrew any nails or screws anchoring the tub flange to studs. Where the tub rests on the floor, use a utility knife to cut through the bead of caulk if there is one.

Use a crowbar to pry the tub an inch or so away from the back wall. Unless the tub is an old-fashioned claw-foot or another type of stand-alone bathtub, it will fit fairly tightly between studs on either side. That means you probably can't slide it out unless you cut away the wall surface on both sides.

The best way is usually to lift the tub on one end. Pry up one end of the tub first with a crowbar, then with 2x4s. Working with a helper, stand the tub upright and slide it out. Once the old tub has been removed, you're ready to install the new one.

Follow these step-by-step instructions to learn how to install a bathtub. Check the drain and replace any damaged parts. Consult the manufacturer's literature and measure to make sure the drain is in the correct location. Screw ledger boards to the studs at the height recommended by the manufacturer.

Ideally, the finish what are temples on your face material should run under hoq tub. Working with the tub turned on its side, dry-fit the overflow tube and the shoe.

Make any how to replace a bathroom tub cuts, then make permanent connections. Place the gasket on bathrlom overflow flange, bahroom it behind the overflow hole, and insert the linkage. Inside the tub, slip the screws into the overflow trim. Hold the overflow flange in place and hand-tighten one of the screws. Start the second screw and tighten both with a screwdriver. Insert the shoe tube into the opening in the overflow tube. Slip the other end batroom the drain bzthroom.

Hold the shoe with one hand while you screw in the flange. Finish tightening with a strainer wrench. Clean away the squeezed-out putty with a plastic putty knife. Before tilting and moving the tub, plan the move so you avoid damaging the waste-and-overflow unit, which protrudes below the tub. It might work best to rest the tub on 2x4s part of the time. Move the tub into position with a helper. You may have to tilt the tub.

Slide it into the opening and gently lower the tub in place, using a helper to guide the overflow tube into the drain line if needed. Slide the drop cloth or any other protective material out from under the tub.

Protect the tub interior. Check the tub for level; an out-of-level tub might not drain completely. Attach the tub to the studs according to the manufacturer's directions. Hoow probably will nail or screw through an acrylic tub flange. For a metal tub, drive nails just above the flange. Working from behind or below, connect the waste-and-overflow tailpiece to the drain line. To test for leaks, close the stopper and fill the tub. Open the stopper; bathrroom and feel for any sign of wetness.

To fill the gap above the tub, cut and install strips of cement backerboard, which is more moisture-resistant than green baathroom. Install tiles to fitallow the adhesive to set for a day, and apply grout.

Apply silicone or tub-and-tile caulk where the tiles meet the tub. By Tib Wilson Updated Reolace 25, Each product how to replace a bathroom tub feature has been independently selected and nan quan mama what can i do by our editorial team.

If you make a purchase using the links included, we may earn commission. Save Pin FB ellipsis More. Credit: Emily Followill.

Top Navigation

Jan 04,  · Follow these step-by-step directions for a bathtub replacement, and you'll be soaking in your new tub in no time. This video shows how easy it is to learn ho.

Last Updated: July 26, References. This article was co-authored by our trained team of editors and researchers who validated it for accuracy and comprehensiveness. There are 25 references cited in this article, which can be found at the bottom of the page.

This article has been viewed , times. Learn more Replacing your tub involves plumbing and carpentry skills, but with the right tools you can do it on your own or with a partner. After disconnecting the drains and pulling out the tub, all you need to do is level the floor and slide the new tub into place. With a little work, you can install a new and updated bathtub in the span of a weekend!

Acrylic and fiberglass tubs are the cheapest and the easiest to maneuver due to their light weight. Cast-iron tubs are durable and hold heat longer, but they are heavier and difficult to maneuver. Tip: Dry-fit the L-shaped pipes to your drains first and measure the length between them to determine how much pipe you need in order to connect the drains together. Make your measurements twice to make sure they're precise before cutting the pipe.

Use hardwood shims since soft wood can deform over time. To replace a bathtub, first you'll need to cut a hole in the wall behind your tub and turn off the water supply to your bathroom.

Then, remove the tub spouts, drains, and drain shoe, and take out the tub surround and drywall around the tub. Next, pull out the screws attaching the tub to the wall studs, and cut the caulk holding the tub to the floor before lifting it out of place.

Finally, once you've removed the old tub, install a new tub in the alcove where the old tub used to be. To learn how to install the new bathtub, scroll down! Did this summary help you? Yes No. Log in Social login does not work in incognito and private browsers. Please log in with your username or email to continue. No account yet? Create an account.

We use cookies to make wikiHow great. By using our site, you agree to our cookie policy. Cookie Settings. Learn why people trust wikiHow. Download Article Explore this Article parts. Tips and Warnings. Things You'll Need. Related Articles.

Article Summary. Part 1 of All rights reserved. This image may not be used by other entities without the express written consent of wikiHow, Inc. Cut a panel behind your tub to access the drain pipes. Most times, the water supply valve for your tub is located in the walls behind the faucet.

Go into the room adjacent to your bathroom to cut a hole in the wall where the drain and faucets are for your tub. Wear safety glasses while working with your saw. Turn off the water supply to your bathroom. The water supply for your tub is either controlled by a valve in the wall behind your faucet or by the main water pump. If you cannot turn off the water for your tub or bathroom, you may need to turn it off for the entire home or building.

Remove the tub spout. Locate the screw on the underside of the faucet or where it connects to the wall. Use a flathead or Phillips screwdriver to remove the screw.

Then, pull it out. Take out the main and overflow drains. A drain removal tool is a cylinder that fits into the drain to loosen its connection to the pipes. Put the end of a drain remover tool in the drain hole and turn it counterclockwise. Keep turning the tool until the drain is loose and you can pull it out by hand. Unscrew the overflow drain, located on the front wall of your tub, and pull it off of the surface.

Some tub drains have screens that you need to remove with a screwdriver before you can use the remover tool. Take out the drain shoe from the access panel you cut. The drain shoe is made up of the pipes that connect the overflow and the main drain to your tub. Look for the T-shaped connector holding the pipes together, and use a pipe wrench to twist the drain shoe off of the main pipes.

Remove the tub surround and drywall around your tub. The surround is the tile or fiberglass on the walls around your tub. Use a pry bar or the back of a claw hammer to rip the surround away from your tub.

When you reach the drywall, use a razor knife to cut out the area around that extends 6 inches 15 cm from the top of your tub until the studs are exposed. If your tub has a surround panel made from fiberglass, you need to take out the entire piece in order to install a new bathtub.

Pull out the nails or screws connecting the tub flange to the studs. The flange around your tub is the raised edge that keeps water from draining into your walls. Use an electric screwdriver or the back of your claw hammer to remove the screws or nails from the flange. Make sure to check each stud around your bath for any nails. Cut any caulk holding the tub the to floor. Run a razor knife through the caulk or sealant surrounding your tub. Cut through the line of sealant that connects the apron, or front of your tub, to the floor.

Grab the tub from the side opposite of the drain and lift it out from its place. Have a partner help slide the tub backward away from the drain pipes. Stand the tub upright and work together to carry it out from your bathroom. Part 2 of Purchase a tub that matches the size and layout of your old one. Measure the size of the alcove and note the drain direction. Use a tape measure to find the maximum length and width of the alcove. Note whether your drain is on the left, right, or center of the tub Find a tub from your local home store that fits in the alcove and has a drain in the same place.

Common Types of Bathtubs Acrylic and fiberglass tubs are the cheapest and the easiest to maneuver due to their light weight. Underlayment is a thin layer of concrete that smooths the surface of your floor.

Check your floor with a level to see if it sits flat. If not, mix the underlayment following the package instructions and spread it across your floor with a flat trowel. Smooth the surface and allow it to dry for 1 day so it has time to set. Underlayment can be purchased from your local hardware store.

Fit the new tub into the alcove and mark the height of the flanges. Set your new tub into the opening where the old one used to be. Make sure your tub sits level on the floor. Use a pencil or marker to trace a line on your studs at the same height as the flanges on your tub. Once you have each stud marked, take the tub out from the alcove again. Attach ledger boards to the studs below your flange marks. Use flat, straight boards that are the same length as the sides of your tub.

Make sure your tub has full contact with the floor after you install the boards. Dry-fit the drains and drain shoe on the new tub. Set your new tub on its side so you can easily access where the drains are placed.

Feed the bottom drain through the hole on the tub and screw it into the L-shaped pipe fitting. Repeat the process with the overflow drain on the side of your tub. Cut the pipes to the length you need using a hacksaw. Tighten the nuts with a pipe wrench. Use a sealant on the drains and pipes to secure the joints in place. ABS glue is a liquid plastic that seals your pipes together. Paint a layer of this glue on the inside and outside of the pipes where they attach on your drain show.

5 thoughts on “How to replace a bathroom tub

Add a comment

Your email will not be published.. Required fields are marked *